The production line is suitable for the automatic production of 0.1L to 5L three -pieces food can. total powder: approx.100KW,total floor space: 350㎡ .total length:approx.50 meters. total manpower: 3-4 people. Production capacity: 300-650cpm.Food tin can’s height range: 60-270mm. Food tin can’s diameter range：52-165mm

Technical flow: cutting the tin sheet to blank—rounding—welding—inner and outer coating (inner powder coating and outer coating)-drying-cooling conveying-necking-flanging/beading/seaming-leak testing-packaging

It consists of three parts(most of them are tinplate)：the bottom , can body and the lid. The can usually has the beading and necking process. Diameter: 52-165mm height : 60-270mm

The first is to put the sheet to a fully automatic resistor welding machine, and from the vacuum suction device to the inlet rolling axis, the single -piece sheet is sent to the roller through the feeding roller to the roll volume rolls. The round shaft is rolled, and then enters the molding device and rolls into a cylindrical tank. The can body is sent to a resistor welding seam machine, and the resistance welding is performed accurately. After welding, the can body is automatically sent to the coating rack. The coating is mainly used to prevent the welding place from contacting the air from the air to cause rust. After the completion , the can body will come to the drying process. The can body is sent to the neck station by holding the can. After completing the neck station, the can body is sent to the next combination machine through the conveyor belt, flanging/beading /sealing can be completed. The can body that completes all processes will be detected by visual detection. After accurate inspection , unqualified products will be detected. Qualified products will come to the packaged workbench for the final packaging.

I Factory workshop preparation:

Reserve the main cable model: YJV3*50+2*25

Area: At least 70 meters long by 10 meters wide, totaling 700 square meters

Flow rate: 2100 liters per minute.

Pressure requirement: 0.4-0.8 Mpa

Number of workers:3-4people

II Preparation of production materials

1、 Top lid, bottom lid, earpiece

① You can directly purchase top lids, bottom lids, and earpieces. In China, there are many specialized lid manufacturing factories that offer various specifications to choose from. If you have specific size requirements, you can request the lid factory to create custom molds for production. Once the production quantity reaches a certain threshold, the cost of mold fabrication is often waived or included for free.

② You can purchase equipment to produce top lids, bottom lids, and earpieces on your own. For more information about the relevant equipment, please click on the following link to learn more.

2、 Can body material of printed tinplate

① You can directly purchase can body materials. In China, there are many professional printing tinplate factories that can customize can body materials according to your requirements.

② You can purchase tin printing equipment to conduct the printing on tinplate on your own. For more information about the relevant equipment, please click on the following link to learn more.

③ You can purchase the Double-side Glue Adhesive Film Laminating Line and process the tinplate yourself. If you would like to learn more about the relevant equipment, please click the link for more information.

3. Copper wire, adhesive, powder, iron wire, plastic glue plug.

These materials can be directly purchased worldwide.

Advantages: the whole production line adopts automatic computer programming control system, fully realizing the full automatic assembly line work.Only 1-2 workers are needed to complete the operation of the entire production line.The whole production line has fast production speed, high production efficiency, automatic fault detection system and low rejection rate.

Disadvantages: compared to semi-automatic production line, the initial investment capital is larger. For the start-up enterprises,It is recommended to use semi-automatic production line with less capital in.

ISHIN product: The vertical method is used. The electrical system adopts the Japanese Mitsubishi PLC programmable program controller, which has an automatic low speed when there is no can; the intelligent protection system is automatically stopped when the can be piled up. The main motor adopts a variable frequency speed adjustment, which has the characteristics of simple operation and convenient mold replacement.

Products in the same industry: ordinary profiles and domestic orbit, lack of stability and accuracy. The head of the machine adopts the old -fashioned design, which has a large production noise, and complicated to change the mold and need more time

The production line is suitable for metal round three pieces can in the food industry. It can also be used in the food can, paint can,, edible oil can, milk powder can, aerosol can production line and so on

Applicable to countries or regions where labor is difficult, unstable, or highly paid. For example: malaysia, indonesia, philippines, vietnam, thailand, india, dubai and so on.

Applicable to countries or regions with high output and high product quality. For example: saudi arabia, dubai, russia, canada, south korea, turkey and so on.

• Established 20 years ago, ISHIN technology is a well-known brand in the Chinese industry.
• More than 80% of customers in China have used ISHIN products.
• ISHIN technology has a strong technical team and professional after-sales service to provide customers with turnkey project and one-stop service.
• Once choosing ISHIN technology products, ISHIN technology will provide you with the most professional technical advice and guidance from material selection, printing and typesetting, installation, commissioning to smooth production